国产免费无码不卡网站_蚪蝌网成人免费无码一级毛片_亚洲首页av免费观看在线_日本综合亚洲三级_上司の部下竹内纱69网站_亚洲AV无码熟妇在线观看_国产成人无码精品亚洲_中美日韩黄色美女网_国产综合久久高清_男人日女人下面视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

single rack cylinder Sold to Canada

Release time:2023-11-18 17:15:30 Hits: Current position: Home > News

This article mainly introduces:

Canada hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

Canada single rack cylinder

(Canada single rack cylinder,produced by Hengyu Group)

single rack cylinder are widely used in Canada,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed single rack cylinder for customers from Canada.

Introduction to single rack cylinder:

The definition of the minimum starting pressure of the single rack cylinder refers to the minimum working pressure of the single rack cylinder in the no-load state, which is a comprehensive index reflecting the manufacturing and assembly accuracy of the single rack cylinder parts and the size of the sealing friction.

In order to ensure the service life of the single rack cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the single rack cylinder, causing damage to the seal and causing leakage in the single rack cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

When the single rack cylinder is installed, the piston and the single rack cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the single rack cylinder head boss is easy to cause scars when it hits the inner surface of the single rack cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized single rack cylinders, only careful and careful operation can be avoided.

single rack cylinders in series, parallel and series parallel. Series: In the single rack cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the single rack cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the single rack cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the single rack cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

Answers to some questions about single rack cylinder:

What are the main technical parameters of the hydraulic cylinder?
Parameters are as follows: 1, cylinder diameter, inner diameter size; 2, import and export diameter and thread parameters; 3, piston rod diameter; 4, cylinder pressure, cylinder working pressure, calculation is often used test pressure, less than 16MPa multiplied by 1.5, higher than 16MPa multiplied by 1.25. 5, cylinder stroke; 6. Is there a buffer? According to the working conditions, the piston rod extension contraction is generally buffered if the impact is large. 7, the installation of the cylinder.

Hydraulic cylinder load algorithm?
If it is thrust, load = working pressure x piston area. If it is pulling force, load = working pressure x(piston area - piston rod area).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP