国产免费无码不卡网站_蚪蝌网成人免费无码一级毛片_亚洲首页av免费观看在线_日本综合亚洲三级_上司の部下竹内纱69网站_亚洲AV无码熟妇在线观看_国产成人无码精品亚洲_中美日韩黄色美女网_国产综合久久高清_男人日女人下面视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

magnetic ring induction cylinder Sold to Denmark

Release time:2023-11-27 15:09:01 Hits: Current position: Home > News

This article mainly introduces:

Denmark hydraulic cylinder,magnetic ring induction cylinder manufacturer,magnetic ring induction cylinder

Denmark magnetic ring induction cylinder

(Denmark magnetic ring induction cylinder,produced by Hengyu Hydraulic Co., Ltd)

magnetic ring induction cylinder are widely used in Denmark,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed magnetic ring induction cylinder for customers from Denmark.

Introduction to magnetic ring induction cylinder:

The cavitation of the magnetic ring induction cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the magnetic ring induction cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

The piston rod of the magnetic ring induction cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

magnetic ring induction cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the magnetic ring induction cylinder is placed for a period of time, the magnetic ring induction cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

The commonly used buffer structure of the magnetic ring induction cylinder is composed of a piston boss and a magnetic ring induction cylinder head groove. When the piston moves close to the magnetic ring induction cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

Answers to some questions about magnetic ring induction cylinder:

How to remove the air in hydraulic cylinder?
Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP