国产免费无码不卡网站_蚪蝌网成人免费无码一级毛片_亚洲首页av免费观看在线_日本综合亚洲三级_上司の部下竹内纱69网站_亚洲AV无码熟妇在线观看_国产成人无码精品亚洲_中美日韩黄色美女网_国产综合久久高清_男人日女人下面视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

crushing machine hydraulic cylinder Sold to Egypt

Release time:2023-11-10 08:34:50 Hits: Current position: Home > News

This article mainly introduces:

Egypt hydraulic cylinder,crushing machine hydraulic cylinder manufacturer,crushing machine hydraulic cylinder

Egypt crushing machine hydraulic cylinder

(Egypt crushing machine hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

crushing machine hydraulic cylinder are widely used in Egypt,because of long service life,smooth movement,high work efficiency.So our company has designed crushing machine hydraulic cylinder for customers from Egypt.

Introduction to crushing machine hydraulic cylinder:

The repair method of crushing machine hydraulic cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

In order to ensure the service life of the crushing machine hydraulic cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the crushing machine hydraulic cylinder, causing damage to the seal and causing leakage in the crushing machine hydraulic cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

When the crushing machine hydraulic cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

The assembly work of the crushing machine hydraulic cylinder has a great impact on the quality of the crushing machine hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about crushing machine hydraulic cylinder:

What is the difference between hydraulic piston cylinder and plunger cylinder?
The force surface of the piston cylinder is a rod cavity and a rodless cavity, and the force surface of the plunger cylinder is the plunger, the spring return single-acting piston cylinder can also rely on the external force of the spring to achieve return, the double-acting piston cylinder can produce tension, and the plunger cylinder only produces thrust without tension.

How to disassemble the big nut that excavate the oil cylinder piston of the excavator?
If you want to be safe, look for a special unloading place for this thing, which is an oil cylinder on top of a turntable with a large nut attached to the center of the turntable. If you're in the field just pin the head of the cylinder to one end, use a big homemade wrench to hold the nut in place, and then get a digging machine and push it down, and it opens.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP